Engine Kits

Diesel service tools

Diesel service tools By Lisle 

Using the correct tools for the job is key,
for getting the job done quickly

Saving you time and making you money

 

Fuel Filter Socket Dodge Cummins Helps Remove and Install Fuel Filters on 5.9 Liter Cummins  Engines. Use the low profile, 29mm socket on the raised hex on the fuel filter housing. 3/8" drive

Oil / Fuel Filter Socket for 6.0L Ford Diesel Removes and Installs Filters on 6 Liter Ford Diesel Pickups. The low profile socket fits both the 35mm and 36mm fuel and oil filters.

 


Truck & Trailer Wheel Pan catches oil from wheel hubs after removing cap. Prevents oil mess during wheel repair. The pan fits rims with 13 3/4" ID and larger. Handle compartments hold hub nuts out of the oil. Made of polypropylene for durability. Will not warp if oil is warm. Capacity 88 ounces.
Truck Brake Cage Bolt Socket Quickly Unlocks Truck Air Brakes. Extra deep 3/4" socket loosens the cage bolt to unlock air brakes on trucks. Also removes the air brake booster for replacement.

 

Fan Clutch Wrench Set for Fords  This wrench set removes and installs Ford fan clutches when repairing or replacing the water pump, timing chain or the fan clutch.  The larger open-end wrench and larger holding wrench that fits Ford 6.9 and 7.3 liter diesel engines

 

Anchor Pin Bushing Remover Also Removes Truck Leaf Spring Bushings. Pneumatic bushing driver set removes and installs truck and trailer anchor pin bushings and stuck anchor pins. Drive the bushing out with the small cone. Use the larger cone to install bushing to the proper depth.

 

Water Sensor Wrench for 2001 and newer GM 6.6L Duramax, removes and installs the water sensor that must be removed when changing your fuel filter. GM conveniently made the sensor out of plastic, and it is 12 sided, so it is very easily damaged by regular tools and pliers that do not specifically fit the sensor

Car and light truck Wheel Stud Installer, easily Installs New Wheel Studs. Use with a ratchet or impact wrench to pull the new stud securely in place. Position the tool over the stud shaft. Tighten the lug nut against the tool to pull the stud in place.

 

Ford Transmission Oil Cooler Line Disconnect Set, 1/2" size for Ford Super Duty Trucks, F250, F350 and F450. Two Sizes, 3/8" and 1/2"  Tip is specially stepped to fit connector. Simply push the line toward the connector, then engage tool and pull line from connector. Designed to Disconnect Transmission Cooler Lines.

Shaft Type Seal Puller, removes Cam Shaft and Crank Shaft Seals Without Damage to the Shaft.
Engage the adjustable hook behind the seal. Brace the push rod against the engine head and push the handle to remove the seal. Removes the seal without damage to the shaft.
a target="_blank" href="/ProductModelDetail.cfm?ProductModelId=26130">Lisle Axle Shaft Seal Installer part number 38060. Drives The Axle Seal Into Place on the Vacuum Operated Front Axles on 1998 to 2004 4-Wheel Drive Ford F-Series Super Duty Trucks.

 


Lisle Heavy Duty Pitman Arm Puller For Ford part number 41970.A heavy-duty puller for the large Pitman arms on Ford 250 and 350 trucks. Jaws are forged and heat-treated for strength.

 

22100 Flywheel Holder and Socket for Duramax Locks Flywheel in Place When Removing Harmonic Balancer on 6.6L Duramax Engines with Allison Automatic Transmission
 Lisle 68210 IPR Socket for Ford Diesel Used to Remove and Replace the Injector Pressure Regulator (IPR) on Ford 6.0L and Other Diesel Engines

 

 



This product is in the following categories:

HomeToolsAll Lisle Specialty Tools

Manufacturer:

Lisle

Part #: 14500

Oil / Fuel Filter Socket for 6.0L Ford Diesel Removes and Installs Filters on 6 Liter Ford Diesel Pickups.
Price: $7.99
Quantity:

Part #: 14600

Fuel Filter Socket Dodge Cummins Helps Remove and Install Fuel Filters on 5.9 Liter Cummins Engines.
Price: $6.99
Quantity:

Part #: 14650

Filter Socket Set for Dodge Cummins fuel filter housing, Ford 6.0L Diesel fuel and oil, and GM Ecotec motors
Price: $24.05
Quantity:

Part #: 22100

Flywheel Holder and Socket for Duramax Locks Flywheel in Place When Removing Harmonic Balancer on 6.6L Duramax Engines with Allison Automatic Transmissions.
Price: $37.60
Quantity:

Part #: 22800

Easily Installs New Wheel Studs
Price: $23.99
Quantity:

Part #: 28950

Semi Truck Wheel Stud Installer, installs most truck wheel studs in seconds
Price: $28.57
Quantity:

Part #: 34350

removes and installs the water sensor that must be removed when changing your fuel filter, or when servicing the water sensor its self
Price: $6.37
Quantity:

Part #: 39960

1/2" size for Ford Super Duty Trucks, F250, F350 and F450. Two Sizes, 3/8" and 1/2"
Price: $6.99
Quantity:

Part #: 56650

Adjustable Seal Puller Head Adjusts to 5 Positions
Price: $13.52
Quantity:

Part #: 58430

Removes Cam Shaft and Crank Shaft Seals Without Damage to the Shaft
Price: $13.99
Quantity:

Part #: 68210

Used to Remove and Replace the Injector Pressure Regulator (IPR) on Ford 6.0L and Other Diesel Engines
Price: $21.99
Quantity: